Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Advanced C&E
#1
Hi all.

I've a mx4 panel and they want to be able to switch cause and effect.

Basically it's one out all out but when a keyswitch is turned it changes to pulsing for 240 seconds and then evac.  Double knock all out.

Turn keyswitch off and it's back to one out all out.

I haven't looked at it yet but was wondering if anybody had any idea how it could be achieved. 


Thanks in advance.
Reply
#2
Not sure but could you not use day more night mode.
Reply
#3
(11-04-2019, 07:12 PM)COMM ENGINEER Wrote: Not sure but could you not use day mode night mode.
Reply
#4
(11-04-2019, 07:12 PM)COMM ENGINEER Wrote: Not sure but could you not use day mode night mode.
Reply
#5
Should be simple enough using ringing styles?
Reply
#6
(11-04-2019, 07:04 PM)Senator Wrote: Hi all.

I've a mx4 panel and they want to be able to switch cause and effect.

Basically it's one out all out but when a keyswitch is turned it changes to pulsing for 240 seconds and then evac.  Double knock all out.

Turn keyswitch off and it's back to one out all out.

I haven't looked at it yet but was wondering if anybody had any idea how it could be achieved. 


Thanks in advance.

Easy enough in relevant output group:


 zone 1-1000 fire ringing style o,

 then add a logic statement of any fire AND  keyswitch (setup key switch as a control signal)ringing style 1 (setup style 1 phase 1  on off pulse phase 2 240 seconds then on).

then add 3rd line any 2 device fires style 0

that should be it

Just thought do you want MCP to over ride pulsing/delay? If no then change all MCPto category B fire otherwise a mcp will be treated as a double knock when the key switch is on
Reply
#7
(11-04-2019, 08:07 PM)Mr C Wrote:
(11-04-2019, 07:04 PM)Senator Wrote: Hi all.

I've a mx4 panel and they want to be able to switch cause and effect.

Basically it's one out all out but when a keyswitch is turned it changes to pulsing for 240 seconds and then evac.  Double knock all out.

Turn keyswitch off and it's back to one out all out.

I haven't looked at it yet but was wondering if anybody had any idea how it could be achieved. 


Thanks in advance.

Easy enough in relevant output group:


 zone 1-1000 fire ringing style o,

 then add a logic statement of any fire AND  keyswitch (setup key switch as a control signal)ringing style 1 (setup style 1 phase 1  on off pulse phase 2 240 seconds then on).

then add 3rd line any 2 device fires style 0

that should be it

Just thought do you want MCP to over ride pulsing/delay? If no then change all MCPto category B fire otherwise a mcp will be treated as a double knock when the key switch is on

Thanks Mr C. Just had a look there. The only issue with what you said is that while keyswitch is on I Will have to turn off the first line ie zone 1-1000 ringing style 0
Reply
#8
Do it the other way round. When keys witch is on, then it bypasses delay. Using RP 1 on style 0
Reply
#9
(11-04-2019, 10:20 PM)Royce44 Wrote: Do it the other way round. When keys witch is on, then it bypasses delay. Using RP 1 on style 0

Just figured that out myself. Lol
Reply
#10
(11-04-2019, 09:51 PM)Senator Wrote:
(11-04-2019, 08:07 PM)Mr C Wrote:
(11-04-2019, 07:04 PM)Senator Wrote: Hi all.

I've a mx4 panel and they want to be able to switch cause and effect.

Basically it's one out all out but when a keyswitch is turned it changes to pulsing for 240 seconds and then evac.  Double knock all out.

Turn keyswitch off and it's back to one out all out.

I haven't looked at it yet but was wondering if anybody had any idea how it could be achieved. 


Thanks in advance.

Easy enough in relevant output group:


 zone 1-1000 fire ringing style o,

 then add a logic statement of any fire AND  keyswitch (setup key switch as a control signal)ringing style 1 (setup style 1 phase 1  on off pulse phase 2 240 seconds then on).

then add 3rd line any 2 device fires style 0

that should be it

Just thought do you want MCP to over ride pulsing/delay? If no then change all MCPto category B fire otherwise a mcp will be treated as a double knock when the key switch is on

Thanks Mr C. Just had a look there. The only issue with what you said is that while keyswitch is on I Will have to turn off the first line ie zone 1-1000 ringing style 0
Sorry yes you are right as Royce said swap it round the other way.

That was a deliberate mistake of course just to make sure you were awake..... well done for spotting it  Biggrin Biggrin
Reply


Possibly Related Threads...
Thread Author Replies Views Last Post
  Advanced call point delays Bero 2 261 11-06-2019, 02:25 PM
Last Post: sparky999
  ems and advanced Advel Tech Support alonso 14 1,024 06-03-2019, 12:55 AM
Last Post: dubfireengineer
  High resistance loop advanced mx pro 5 dcarney 18 4,796 05-05-2018, 09:09 PM
Last Post: Monkeh
Rolleyes Advanced Mx config output evac Bero 4 1,314 04-04-2018, 10:28 PM
Last Post: Graeme
  Advanced loop card short circuit testing xenex100 60 30,727 06-03-2018, 10:07 PM
Last Post: Monkeh
  Advanced MX Software Service Tools Midpat Fire 5 2,039 28-02-2018, 11:59 PM
Last Post: Tilly
  Advanced diagnostic mode logs luggsey 22 5,531 09-02-2018, 12:12 AM
Last Post: sparky999
  Advanced mxpro 5 quick start user guide Monkeh 3 1,740 17-12-2017, 02:16 PM
Last Post: sparky999
  Advanced apollo blown loop card alonso 12 5,727 27-07-2017, 12:33 PM
Last Post: MD Martin
  Advanced pro5 & Apollo 3 channel I/o Clarkie 12 5,978 26-07-2017, 11:51 PM
Last Post: Graeme

Forum Jump:


Users browsing this thread: 1 Guest(s)